Oil content is the number that decides whether a lot of desiccated coconut is full-fat or low-fat, and therefore what it should cost. It is also the number buyers and mills most often disagree about after the container lands.
The disagreement is rarely about grade names. It is about how the oil was measured, on what basis, and what tolerance the contract allows. A one-point gap between a mill COA and a destination lab can be the difference between a lot that passes and a lot that triggers a claim.
This note covers the measurement side. For grade definitions and the cost-per-kilo-of-fat arithmetic, see our earlier piece on high-fat vs low-fat desiccated coconut.
Where are the oil-content lines drawn?
Codex draws two lines. CXS 177-1991 requires at least 60% m/m oil for desiccated coconut made without oil extraction. Where oil has been partly removed by physical means, it allows 35% up to but not including 60%.
Producer bodies slice the range more finely. The Asian and Pacific Coconut Community (APCC) describes high-fat product at 60-65% oil, medium or reduced-fat at 50-60% and low-fat at 40-50%. Its quality standard sets oil at not less than 60%, with moisture capped at 3.0% for standard grades and 4.5% for special cuts.
| Source | Full-fat | Reduced or low-fat |
|---|---|---|
| Codex CXS 177 | ≥ 60% m/m | 35% to < 60% m/m |
| APCC product description | 60-65% | 50-60% (medium), 40-50% (low) |
| Philippine PNS/BAFPS 25:2007 | ≥ 62% m/m | not recognised |
Sources: Codex; APCC; PNS/BAFPS 25:2007.
A supplier quoting “low-fat” may mean 55%, 45% or 38%. Those are three different products. The word alone is not a spec.
Which test method does the standard name?
Codex names AOAC 948.22 for oil content, classed as a gravimetric method. Moisture goes to AOAC 925.40 (loss on drying), ash to AOAC 950.49, and total acidity of the extracted oil to ISO 660:2009 or AOCS Cd 3d-63. Section 10 of the standard lists all four.
Gravimetric means the oil is extracted with a solvent, the solvent is driven off, and the residue is weighed. The result depends on the solvent, the extraction time and how finely the sample is ground. Two labs that follow different procedures can both be competent and still report different numbers.
Desk practice is to name the method in the contract, not just the number. ISO 659:2009 is a hexane-extract reference method for oilseeds used as industrial raw materials. It is a sound method, but its scope does not mention desiccated coconut, so it should not be swapped in silently.
Does the oil figure include or exclude moisture?
Codex states the oil limits as m/m, mass of oil per mass of product as tested. It does not mention a dry-matter basis. The desk reads that as an as-received figure, and buyers should say so in writing.
The basis matters because some mill reports quote fat on a dry basis. At 3% moisture, a product showing 65% oil on a dry basis carries about 63.05% as received (65 × 0.97). Against a 64% as-received floor, that is a rejection. Against a 62% floor it passes.
Always write the basis next to the number.
What does the sample have to represent?
A lot of 20 tonnes in 25 kg bags is 800 bags. A lab tests perhaps 10 to 50 grams of it. Sample preparation therefore drives the answer as much as the extraction does.
Fat can separate and migrate inside bulk coconut, particularly in finer cuts that have been through a mill. Samples drawn only from the top of a bag, or from the first bags off a line, can read high or low. A composite drawn across the lot, ground and sub-sampled by the lab, is the defensible basis for a dispute.
Codex ties lot acceptance to a sampling plan referenced in Section 10 and to a count of defective containers. Its own sampling guidance, CXG 50, describes the plans as intended mainly for inspection of food on receipt, for example by importing-country authorities. A commercial contract should therefore agree its own sampling clause. For the pre-shipment side, see what to ask a pre-shipment inspector.
How do oil, moisture and acidity interact on a COA?
They are read together. A lot can meet its oil floor and still fail on acidity. The Codex limit for total acidity of the extracted oil is 0.3% m/m as lauric acid; APCC lists 0.15% to 0.30%.
Product held warm or stored long can pick up moisture and develop free fatty acids. On an as-received basis, the oil percentage drifts down as water is absorbed. The guide to reading a desiccated coconut COA walks through that cross-check, and the moisture and water activity note covers the other side.
What contract wording closes the gap?
Five items, all short:
- Oil content as a minimum, with a numeric figure, stated as m/m as received.
- The reference method by number (AOAC 948.22 if you follow Codex).
- A moisture ceiling, with its method.
- A sampling clause: composite across the lot, with sealed retained samples.
- A dispute route: a named umpire lab, with its result binding.
On tolerance, ask the testing lab for the repeatability and reproducibility figures of its method and set the contract tolerance no tighter than those. A spec stricter than the test can resolve will generate disputes nobody can win.
What this means for buyers
- Procurement, CPG (A): write “oil content 62% m/m minimum, as received, AOAC 948.22” instead of “full-fat”. Add moisture and acidity with their methods.
- Importers and distributors (B): check which basis the mill reports on before comparing two offers. A dry-basis figure flatters the product by roughly the moisture percentage.
- Brand owners (C): if a label or formulation relies on a fat declaration, keep a retained sample from each lot and test it at your own accredited lab.
- Traders and brokers (D): low-fat offers described only by name are not comparable. Ask for the actual oil percentage before quoting a spread.
FAQ
What is the oil content of full-fat desiccated coconut? Codex requires at least 60% m/m for desiccated coconut made without oil extraction. The Philippine national standard PNS/BAFPS 25:2007 sets 62%. APCC describes high-fat grades at 60-65%.
Which method does Codex use to test oil content? Codex CXS 177 names AOAC 948.22, a gravimetric method. It names AOAC 925.40 for moisture and ISO 660:2009 or AOCS Cd 3d-63 for acidity of the extracted oil.
Is oil content reported on a dry or as-received basis? Codex states m/m and does not mention a dry basis. Mill COAs can differ, so the contract should state the basis. At 3% moisture, 65% dry-basis oil is about 63% as received.
Why do two labs report different oil percentages? Different solvent, extraction time, grinding or sampling. Gravimetric methods are sensitive to procedure. Naming the method and an umpire lab in the contract prevents most of these arguments.
What counts as low-fat desiccated coconut? Under Codex, 35% to below 60% oil. Trade bands vary: APCC describes low-fat at 40-50%. Always ask for the actual percentage.
Need an oil-content spec written and held across origins? Send the desk an RFQ for desiccated coconut.